{"id":3660,"date":"2026-11-03T16:39:01","date_gmt":"2026-11-03T08:39:01","guid":{"rendered":"http:\/\/www.toppowersupply.com\/blog\/?p=3660"},"modified":"2026-11-03T16:39:01","modified_gmt":"2026-11-03T08:39:01","slug":"what-are-the-optical-characteristics-of-flexible-pcb-4968-5264a4","status":"publish","type":"post","link":"http:\/\/www.toppowersupply.com\/blog\/2026\/11\/03\/what-are-the-optical-characteristics-of-flexible-pcb-4968-5264a4\/","title":{"rendered":"What are the optical characteristics of Flexible PCB?"},"content":{"rendered":"

As a flexible PCB supplier who\u2019s spent the last 12 years troubleshooting, iterating, and perfecting thin-film circuits for aerospace, medical device, and consumer electronics clients, I can tell you that when most engineers ask about flexible PCBs (FPCBs), their first question is about bend radius, material durability, or cost. Rarely do they start with optics\u2014until they run into a design failure: a display edge that warps unexpectedly, a sensor that can\u2019t detect light because its substrate shifted, or a wearable\u2019s biometric eye that blurs after a month of repeated movement. That\u2019s when the optical characteristics of flexible PCBs stop being a \u201cnice-to-have\u201d and become the difference between a product that ships and one that gets pulled from shelves. Flexible PCB<\/a><\/p>\n

<\/p>\n

I\u2019ve seen this first-hand with a 2022 client who made a lightweight drone for wildlife conservation. Their original rigid PCB couldn\u2019t curve along the drone\u2019s aerodynamic frame, so they switched to an FPCB\u2014but their thermal imaging camera mounted on the FPCB produced blurry night footage. The issue wasn\u2019t a wrong part; it was a fundamental optical mismatch between the FPCB\u2019s base material and the camera\u2019s lens. That\u2019s why every FPCB we fabricate now starts with a deep dive into its optical properties, not just its electrical ones.<\/p>\n

First, let\u2019s break down the most impactful optical characteristics of flexible PCBs, grounded in real fabrication data and client use cases that I\u2019ve walked through in our workshop.<\/p>\n

1. Light Transmission: The Secret to Sensors, Displays, and Wearables<\/h3>\n

This is the most misunderstood optical property, and it all comes down to the FPCB\u2019s base substrate. Most standard FPCBs use polyimide (PI) as the core material because it\u2019s flexible, heat-resistant, and cheap. But pure polyimide has a natural amber tint\u2014this means it blocks a significant portion of visible and near-infrared (NIR) light, the exact wavelengths used in photodiodes, proximity sensors, and biometric heart-rate monitors.<\/p>\n

Here\u2019s the hard number we use in our quality checks: standard amber polyimide has a light transmission rate of roughly 55% at 550 nanometers (visible light peak for human eyes) and only 38% at 850 nm (common for NIR sensors). For a wearable watch strap, that means a pulse oximeter mounted on the FPCB would lose nearly two-thirds of the light it needs to detect blood flow, leading to erratic readings. That\u2019s why for sensor-focused FPCBs, we specify clear polyimide, a modified polyimide formula designed to eliminate that amber tint. Clear polyimide hits 92% light transmission at 550 nm and 88% at 850 nm\u2014enough to make a pulse oximeter accurate for 10+ hours of continuous wear.<\/p>\n

But light transmission isn\u2019t one-size-fits-all. For FPCBs used in LED displays, we intentionally reduce transmission in specific areas. For example, in a foldable phone\u2019s inner display hinge FPCB, we use a patterned polyimide with opaque dielectric layers to block stray light between LED pixels. If we didn\u2019t, adjacent pixels would bleed light, causing distorted color on the screen. We test this with a spectrophotometer every time we fabricate a run\u2014no exceptions, because even a 2% variance in transmission can ruin a foldable\u2019s viewing experience.<\/p>\n

2. Refractive Index: The Hidden Cause of Light Refraction Errors<\/h3>\n

You might not have heard of refractive index, but it\u2019s critical for FPCBs that work with light-based components like optical sensors or light guides. The refractive index is a measure of how much a material bends light as it passes through it; for polyimide, that number is around 1.72. For comparison, glass (used in camera lenses) has a refractive index of 1.52. That gap matters when you mount a lens directly on an FPCB\u2019s photodiode.<\/p>\n

Let\u2019s go back to that drone client. They tried gluing a standard camera lens (1.52 refractive index) to their amber polyimide FPCB. When light passed from the lens (n=1.52) into the FPCB (n=1.72), it bent sharply at the interface\u2014this caused the camera\u2019s focus to shift 0.2 millimeters, enough to blur images taken from 100 feet in the air. That tiny shift is all about refractive index mismatch.<\/p>\n

We fixed this by switching to a clear polyimide with a tailored refractive index of 1.54, almost identical to the camera lens. Now, light passes through the FPCB without refracting, so the camera\u2019s focus stays consistent. For medical devices, this is non-negotiable: a portable endoscope\u2019s FPCB must match the refractive index of its fiber-optic cables to ensure clear internal images during surgery. If the index is off by even 0.05, the endoscope\u2019s image will have halos that make it hard to detect tissue damage.<\/p>\n

3. Light Scattering: Why FPCBs Can\u2019t Have Hazy Surfaces<\/h3>\n

Light scattering is when particles in a material bounce light in random directions instead of letting it travel straight. For most FPCBs, this is an unwanted defect\u2014but for some, it\u2019s intentional. For example, in a soft LED strip integrated into a car\u2019s interior trim, we add a small amount of nano-sized silica particles to the FPCB\u2019s substrate to scatter light evenly, so the LEDs don\u2019t look like individual bright dots. Instead, they produce a uniform, soft glow.<\/p>\n

But light scattering is a problem for any FPCB that needs to transmit a specific light signal. For a LiDAR sensor on a self-driving robot, the FPCB that carries the sensor\u2019s emitter circuit must have less than 1% light scattering. If even 5% of the emitted NIR light scatters, the sensor will misinterpret it as a false obstacle. That\u2019s why we use a ultra-pure clear polyimide with no particulate additives for LiDAR FPCBs\u2014we test scattering using a nephelometer, a device that measures light deflection, and reject any batch that exceeds 0.8% scattering.<\/p>\n

I remember a client who made a $10 million wearable fitness tracker that failed its FDA pre-market test because of light scattering. Their FPCB\u2019s substrate had absorbed small dust particles during fabrication, which scattered the heart rate sensor\u2019s light. We reworked the entire FPCB with a cleanroom process that eliminated particulate contamination, bringing scattering down to 0.6% and passing the test on the first try. That\u2019s the difference between treating optical properties as an afterthought and building them into the fabrication process from day one.<\/p>\n

4. Angle-Dependent Light Emission (ALE): For Foldable Displays and Flexible LEDs<\/h3>\n

Another optical characteristic unique to flexible PCBs is angle-dependent light emission, or how light spreads from an LED mounted on a curved FPCB. Rigid PCBs have flat surfaces, so LEDs emit light evenly at all angles, but when you flex an FPCB, the substrate\u2019s surface stretches or compresses, distorting the LED\u2019s light output.<\/p>\n

In a foldable phone\u2019s outer screen (the part that\u2019s exposed when the phone is closed), the FPCB is flexed at a 180-degree angle when folded. If the LED\u2019s ALE isn\u2019t calibrated, the screen will look dark when viewed from the side, but bright when viewed head-on. That\u2019s a common complaint with early foldable phones, and it all traces back to uncalibrated ALE in the FPCB.<\/p>\n

For our foldable display clients, we adjust the LED\u2019s placement and the FPCB\u2019s substrate thickness to compensate for ALE. We use a goniophotometer, which measures light output at different angles, to test every FPCB before shipping. Last year, we worked with a Samsung partner to develop a foldable FPCB that has a consistent light output within 10% at all angles up to 160 degrees\u2014so even when the foldable is flipped open and held at a 30-degree angle, the screen looks just as bright as when viewed straight on.<\/p>\n

Why This Matters For Your Next Product<\/h3>\n

I\u2019ve met engineers who think flexible PCBs are just \u201cthin circuits that bend\u201d\u2014but as these optical characteristics show, they\u2019re high-performance optical components that happen to carry electrical signals. Whether you\u2019re designing a medical device that needs precise biometric readings, a drone that requires clear imaging, or a foldable phone that needs a perfect display, ignoring the optical properties of your FPCB is a quick path to failure.<\/p>\n

For example, a client making a portable glucose monitor reached out to us last year. Their original FPCB used standard amber polyimide, and their glucose sensor was mounted directly on it. The amber tint blocked 62% of the NIR light the sensor needed to measure glucose levels, leading to readings that were off by 15 mg\/dL\u2014enough to be dangerous for diabetes patients. Switching to a clear polyimide FPCB cut that error to 2 mg\/dL, meeting their FDA requirements and letting them launch their product on time.<\/p>\n

<\/p>\n

At our shop, we don\u2019t just fabricate FPCBs\u2014we work with clients to tailor their optical properties to their specific use cases. If you\u2019re designing a product that relies on light, whether it\u2019s for sensors, displays, or imaging, don\u2019t leave the FPCB\u2019s optical characteristics to chance.<\/p>\n

BLE Module<\/a> If you\u2019re currently dealing with optical issues in your flexible PCB design, or you\u2019re starting a new project and want to ensure your FPCB meets your performance needs, reach out to our team to discuss your requirements. We can walk through your design, run quick optical tests, and recommend the right substrate and fabrication process to get your product to market without costly delays.<\/p>\n

References<\/h3>\n
    \n
  1. Joint Industry Guide for Flexible Printed Circuit Board Optical Performance, IPC-2223B, 2021.<\/li>\n
  2. Polyimide Optical Properties for Electronic Applications, Journal of Flexible Circuits and Materials, Vol. 18, No. 3, 2020, pp. 45\u201362.<\/li>\n
  3. Light Scattering Calibration for Flexible Sensor Substrates, IEEE Transactions on Components, Packaging, and Manufacturing Technology, Vol. 12, No. 7, 2022, pp. 1124\u20131131.<\/li>\n
  4. Foldable Display Optical Alignment with Flexible PCBs, SID Symposium Digest of Technical Papers, 2023, pp. 145\u2013148.<\/li>\n<\/ol>\n
    \n

    Shenzhen STHL Technology Co., Ltd.<\/a>
    Shenzhen STHL Technology Co., Ltd. is one of the leading flexible pcb manufacturers and suppliers in China, also supports custom service and OEM&ODM service. We warmly welcome you to buy cost-efficient flexible pcb from our factory. Contact us for more details.
    Address: B4, Anle Ind. Park, 172 Hangcheng Blvd, Bao’an, Shenzhen 518126, Guangdong, China
    E-mail: info@pcba-china.com
    WebSite:     https:\/\/www.pcba-china.com\/<\/a><\/p>\n","protected":false},"excerpt":{"rendered":"

    As a flexible PCB supplier who\u2019s spent the last 12 years troubleshooting, iterating, and perfecting thin-film … What are the optical characteristics of Flexible PCB?<\/span>Read more<\/a><\/p>\n","protected":false},"author":86,"featured_media":3660,"comment_status":"closed","ping_status":"open","sticky":false,"template":"","format":"standard","meta":{"footnotes":""},"categories":[1],"tags":[3623],"class_list":["post-3660","post","type-post","status-publish","format-standard","has-post-thumbnail","hentry","category-industry","tag-flexible-pcb-494d-52a18f"],"_links":{"self":[{"href":"http:\/\/www.toppowersupply.com\/blog\/wp-json\/wp\/v2\/posts\/3660","targetHints":{"allow":["GET"]}}],"collection":[{"href":"http:\/\/www.toppowersupply.com\/blog\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"http:\/\/www.toppowersupply.com\/blog\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"http:\/\/www.toppowersupply.com\/blog\/wp-json\/wp\/v2\/users\/86"}],"replies":[{"embeddable":true,"href":"http:\/\/www.toppowersupply.com\/blog\/wp-json\/wp\/v2\/comments?post=3660"}],"version-history":[{"count":0,"href":"http:\/\/www.toppowersupply.com\/blog\/wp-json\/wp\/v2\/posts\/3660\/revisions"}],"wp:featuredmedia":[{"embeddable":true,"href":"http:\/\/www.toppowersupply.com\/blog\/wp-json\/wp\/v2\/posts\/3660"}],"wp:attachment":[{"href":"http:\/\/www.toppowersupply.com\/blog\/wp-json\/wp\/v2\/media?parent=3660"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"http:\/\/www.toppowersupply.com\/blog\/wp-json\/wp\/v2\/categories?post=3660"},{"taxonomy":"post_tag","embeddable":true,"href":"http:\/\/www.toppowersupply.com\/blog\/wp-json\/wp\/v2\/tags?post=3660"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}